Using a wrench, turn and lock the taps securely over the ridges. Name required Email will not be published required Website By submitting you agree to our. Batch feed disposals, which are a bit more expensive, require the use of a stopper prior to operation, which can be safer in households with kids. Once you have turned the off, plug converter box into wall outlet. Electrical Requirements When replacing an existing garbage disposal, you can just use the necessary electrical power and switch. Turn under the sink and install the mounting gasket and retaining ring on the flange just as instructed by the manual from the manufacturer.
Carefully arrange the flange, mounting ring, and the snap ring and screw them to hold them securely beneath the sink. Edit: There are outlets under the sink, just no switch to control them. Holding the disposal in place, turn the lower mounting ring until all three tabs are locked into the mounting assembly. To install a disposal to a double sink, you need to follow the process below and have the necessary materials and tools. It's important to keep safety top of mind since you'll be working with water and an electrical appliance. Be aware that the disposal may contain water and food waste, so carry it outside right-side up. Remove the disposal by inserting a screwdriver into the mounting ring lug and turning counterclockwise until it comes loose.
Take your time, and if you don't feel comfortable, you should. Simply wipe the areas under the sink with clean water. This is shown in the pictures below. Step 3 — Attach the Tube to the Button Attach one end of air tube to bottom of air switch button and the other end to the white nib on the black converter box. Fix the new sink flange through the sink opening and push it to hold firmly. Collin, from Grand Rapids, Michigan Thank you for answering my question. After you are through, make sure to apply clamps to secure the connection.
See Fig 1b Disconnect the electrical. Step 4: Preparing to Install New Unit How do you prepare for the new unit? This article primarly covers installing a garbage disposal for the first time. Step 2: Install the New Disposal Unit The preparation process of installing a disposal unit to a double sink is slightly different if you have to prepare the second sink differently. It is doable but more information is needed to accurately say pricewise Atlantic Askthehandyman. Step 3: Connect the Electrical Once you are sure that you have mounted the garbage disposal on the first sink securely and the second sink is well fixed, now is time to connect the electrical wires. I'm glad this disposal wiring diagram was helpful for you.
Certain links direct you to affiliate sites which may pay a referral fee. We had a button add-on installed so it acts like a switch. Step 1: Remove the Broken Disposal Unit This applies to people with an old faulty unit that they want to replace with a new unit installed to a double sink. Be sure to use a two screw cord connector when attaching the cord to the disposal. Note: The switch I link to is the newer model.
The tee will allow you to attach the discharge tube to the disposal unit in the first sink. If I didn't know better I would think I was an electrician. Disconnect the discharge tube and the entire drainage system from the second sink. I'm glad this helped you with your kitchen disposal wiring. This site provides information based on the research and opinions of our contributors. Step 4: Connect the Drains Attach the discharge tube with the flange and the screws or bolts. This reduces the potential of an electric shock when your hands are wet.
Test the bare ends of the wires with an electrical voltage tester to make sure they are not charged see. Installing to Double Sink If you own a double sink in your kitchen, you will definitely want to have all of them fitted with a garbage disposal unit. Place a bead of plumber's putty around the sink flange of a new garbage disposal kit, and set the flange evenly into the sink hole. Scrap it off gently with a putty knife or a fine wire for one that is stubborn to remove. This article has also been viewed 169,592 times. The center wire is typically the ground and in most cases the ground wire, and with some cords the ground wire has green insulation.
You can also disconnect the down drain pipe that comes from the sink and the p-trap. That would help for access to power. Insert the flange into the drain hole and press down evenly to attach it. We are wanting to install one, but there's also no switch nearby to turn it on or off. Afterwards, lay down the unit and connect the power cord from the power mains. Make sure the screws are tight enough to hold it firmly. The big thing is the power source and another question, is this the first floor with a basement underneath? Help with Home Wiring Wiring Parts and Tools Home Electrical Directories Electrical Wiring Resources Recent Testimonials I think your site offers the the clearest and best electrical information for homeowners I have ever seen on the net.
Step 2 — Mount the Button Use the rubber gasket above the counter for the air switch on the outside and tighten with plastic nut from below your sink. Lay the disposal on its side under the sink so you can make the electrical connections. Turn off the electricity to the sink. Connect the white wires in similar fashion, then wrap the end of the bare wire around the green grounding screw and tighten the screw with a screwdriver. Then tuck the wires into the compartment, and replace the cover.
Finally, run water into the sink and turn on the disposal to make sure that it works. You have given me confidence to do my own projects which I never had before. Additionally, ensure the wiring is done well. Never pay a large deposit to start the work. You can install a garbage disposal in a single sink in a couple of hours with some basic hand tools.